• 首页
  • 关于期刊
    期刊简介
    编委会
    青年编委会
    合作单位
    《药学研究》编辑部
  • 投稿指南
  • 制度与声明
    出版伦理规范
    学术不端声明
    开放获取(OA)声明
    AIGC工具使用声明
  • 期刊订阅
  • 下载中心
  • English
引用本文:陈铭,王琛,张志强,段美涛,任君刚,林海婷.熔融沉积3D打印技术制备对乙酰氨基酚缓释片及其制剂学评价[J].药学研究,2024,43(2):142-148[点击复制]
【打印本页】      【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2974次   下载 3119次 本文二维码信息
码上扫一扫!
熔融沉积3D打印技术制备对乙酰氨基酚缓释片及其制剂学评价
陈铭,王琛,张志强,段美涛,任君刚,林海婷
字体:加大+|默认|缩小-
(厦门医学院,福建 厦门 361000)
摘要:
目的 基于熔融沉积成型技术制备对乙酰氨基酚(APAP)片并进行质量评价,为该技术应用于对乙酰氨基酚片剂的3D打印提供实验依据。方法 利用热熔挤出技术制备打印线材,后利用熔融沉积成型3D打印技术制备成型片剂。筛选过程中以片剂打印的完整性来确定增塑剂的用量,以体外释放累积百分率确定致孔剂的用量,最后以正交设计确定最优处方及工艺参数,并对所制备片剂的性能进行评价。结果 最终确定以乙基纤维素(EC)为载体辅料、柠檬酸三乙酯(TEC)为增塑剂、羟丙基甲基纤维素(HPMC)为致孔剂进行制备,最佳比例为APAP∶塑化EC∶HPMC=25∶50∶25,TEC用量为20% EC,打印温度为160 ℃。该片剂的6 h累计释放率约为50%,24 h内体外释放度达90%以上。结论 采用3D打印技术成功制得对乙酰氨基酚片剂,所得产品外表完整,层间叠加较平整,含量测定合格,体外释放较上市对乙酰氨基酚片剂缓慢,药物活性分子在试验温度下含量稳定。
关键词:  熔融沉积成型技术  3D打印  对乙酰氨基酚  制备工艺
DOI:10.13506/j.cnki.jpr.2024.02.007
基金项目:厦门医学院校级课题[No.KPT2020-03(2)]
Preparation of Acetaminophen sustained-release tablets using melt deposition 3D printing technology and its pharmaceutical evaluation
CHEN Ming,WANG Chen,ZHANG Zhiqiang,DUAN Meitao,REN Jungang,LIN Haiting
(Xiamen Medical College, Xiamen 361000, China)
Abstract:
Objective In this study, the feasibility of fused deposition molding (FDM) technology for the preparation of paracetamol (APAP) tablets was studied, which provided experimental basis for the application of this technology in 3D printing of paracetamol tablets.Methods The preparation of the tablets described in this paper is divided into two steps: using hot melt extrusion (HME) technology to prepare the printed wire; using the fused deposition modeling technology to prepare the molding tablets. During the screening process, the amount and types of excipient, plasticizer, and pore-forming agent were determined. Then the optimal prescription and process parameters were screened by orthogonal design. Finally the content determination, in vitro release, scanning electron microscope and thermogravimetric analysis were evaluated.Results The final optimized 3D printed APAP tablets prescription was including ethyl cellulose (EC) as skeleton excipient, triethyl citrate (TEC) as plasticizer and hypromellose as pore-forming agent, with the ratio of APAP∶Plasticized EC∶HPMC= 25∶50 ∶25, the optimized printing temperature was 160 ℃. The in vitro release rate of tablets was about 50% at 6 hour and was over 90% within 24 hours.Conclusion APAP tablets were successfully prepared using 3D printing technology. The resulting product appears a flat surface and the stacking of layers is relatively smooth. The tables has a slower in vitro release rate compared to APAP tables on the market. The content determination was qualified and the active pharmaceutical ingredient is stable in content at the test temperature.
Key words:  Fused deposition molding technology  3D printing  Acetaminophen  Technology of preparation
今日访问量:2646    总访问量:55339161
网站版权:《药学研究》编辑部     鲁ICP备17018036号-3     鲁公网安备 37010202001351号
主办:山东省食品药品检验研究院、山东省药学会 地址:山东省济南市高新区新泺大街2749号 邮政编码:250101
电话:0531-81216586 电子邮箱:yaoxueyanjiu@163.com;yaoxueyanjiu@126.com
技术支持:北京勤云科技有限公司