• Home
  • About Journal
    Journal Introduction
    Editorial Board
    Youth Editorial Board
    Cooperating Institutions
    Editorial Department
  • Submission Guidelines
  • Policies & Statements
    Ethical Guidelines for Publication
    Academic Misconduct Statement
    Open Access (OA) Statement
    AIGC Use Statement
  • Journal Subscription
  • Download Center
  • 中文版
Cite this article:
SONG Yanjun,PU Xufeng,ZHU Peng,LIU Xiaoshuang.Study on the freeze dryer process of parecoxib sodium for injection[J].Journal Of Pharmaceutical Research,2016,35(5):272-275,307[Click to copy]
【Print this page】      【Download PDF Full Text】   【View/Add Comment】  【Download reader】  【 Close 】
←Previous|Next→ Archive    Advanced Search
This article has been viewed: 3527times   Download 3416次 QR Code for this article
Scan with your phone!
注射用帕瑞昔布钠的冻干工艺研究
宋岩珺1,蒲旭峰1,朱鹏2,刘小双1
Font:Larger+|Default|Smaller-
(1.成都中医药大学药学院,四川 成都 610072;2.成都欣捷高新技术开发有限公司,四川 成都 610041)
摘要:
目的 研究注射用帕瑞昔布钠最佳冻干制备工艺条件。方法 通过部分因子分析实验,以水分、有关物质、含量等为指标优化冻干工艺,其中考察因素为冻干时间和干燥工艺,每个因素取3个水平。结果 注射用帕瑞昔布钠的最佳冻干工艺条件为:真空度25 Pa,-40 ℃预冻4 h,0 ℃真空干燥15 h,35 ℃再干燥10 h即得。所制得注射用帕瑞昔布钠粉针剂经加速1、2、3月后性状、含量等指标无明显变化。结论 选定的工艺可行,产品符合药典注射剂项下的各项要求。
关键词:  注射用帕瑞昔布钠  制剂工艺  试验设计
DOI:10.13506/j.cnki.jpr.2016.05.008
基金项目:
Study on the freeze dryer process of parecoxib sodium for injection
SONG Yanjun1,PU Xufeng1,ZHU Peng2,LIU Xiaoshuang1
(1.Department of Pharmacy,Chengdu University of Troditional Chinese Medicine,Chengdu 610072,China;2.Chengdu Giantech hi-technology development Co..ltd,Chengdu 610041,China)
Abstract:
Objective To study the optimum technological conditions of Freeze-dryed Parecoxib Sodium for Injection.Methods the freeze drying process was optimized which takes the water content,related substances,content etc.as the indicators by partial factor analysis test,the following factors with three levels were considered:freeze-dryed time and drying process.Results The optimum technologies of freeze dryer were:vacuum was estimated to be 25 Pa,pre-freeze for 4h at -40 ℃,vacuum dryer for 15 h at 0 ℃, dryer for 10 h at 35 ℃.In the accelerated stability test for 1,2,3 months,there was no significant change on character,content etc for parecoxib sodium for injection products.Conclusion The technology was feasible,the quality of infusion was fit the requirement of injection.
Key words:  Parecoxib Sodium for Injection  Preparation process  Design of experiments
Today's Visits:488    Total Visits:2383203
Website copyright:Editorial Board of Journal of Pharmaceutical Research     鲁ICP备17018036号-3     鲁公网安备 37010202001351号
Sponsored by:Shandong Institute for Food and Drug Control Shandong Pharmaceutical Association Address:No.2749 Xinluo Street,High-Tech Zone,Jinan,P.R.China Postcode:250101
Telephone Number:0531-81216586 Email :yaoxueyanjiu@163.com;yaoxueyanjiu@126.com
Technical Support:Beijing Qinyun Technology Co., Ltd.