• Home
  • About Journal
    Journal Introduction
    Editorial Board
    Youth Editorial Board
    Cooperating Institutions
    Editorial Department
  • Submission Guidelines
  • Policies & Statements
    Ethical Guidelines for Publication
    Academic Misconduct Statement
    Open Access (OA) Statement
    AIGC Use Statement
  • Journal Subscription
  • Download Center
  • 中文版
Cite this article:
CHEN Ming,WANG Chen,ZHANG Zhiqiang,DUAN Meitao,REN Jungang,LIN Haiting.Preparation of Acetaminophen sustained-release tablets using melt deposition 3D printing technology and its pharmaceutical evaluation[J].Journal Of Pharmaceutical Research,2024,43(2):142-148[Click to copy]
【Print this page】      【Download PDF Full Text】   【View/Add Comment】  【Download reader】  【 Close 】
←Previous|Next→ Archive    Advanced Search
This article has been viewed: 2975times   Download 3119次 QR Code for this article
Scan with your phone!
熔融沉积3D打印技术制备对乙酰氨基酚缓释片及其制剂学评价
陈铭,王琛,张志强,段美涛,任君刚,林海婷
Font:Larger+|Default|Smaller-
(厦门医学院,福建 厦门 361000)
摘要:
目的 基于熔融沉积成型技术制备对乙酰氨基酚(APAP)片并进行质量评价,为该技术应用于对乙酰氨基酚片剂的3D打印提供实验依据。方法 利用热熔挤出技术制备打印线材,后利用熔融沉积成型3D打印技术制备成型片剂。筛选过程中以片剂打印的完整性来确定增塑剂的用量,以体外释放累积百分率确定致孔剂的用量,最后以正交设计确定最优处方及工艺参数,并对所制备片剂的性能进行评价。结果 最终确定以乙基纤维素(EC)为载体辅料、柠檬酸三乙酯(TEC)为增塑剂、羟丙基甲基纤维素(HPMC)为致孔剂进行制备,最佳比例为APAP∶塑化EC∶HPMC=25∶50∶25,TEC用量为20% EC,打印温度为160 ℃。该片剂的6 h累计释放率约为50%,24 h内体外释放度达90%以上。结论 采用3D打印技术成功制得对乙酰氨基酚片剂,所得产品外表完整,层间叠加较平整,含量测定合格,体外释放较上市对乙酰氨基酚片剂缓慢,药物活性分子在试验温度下含量稳定。
关键词:  熔融沉积成型技术  3D打印  对乙酰氨基酚  制备工艺
DOI:10.13506/j.cnki.jpr.2024.02.007
基金项目:厦门医学院校级课题[No.KPT2020-03(2)]
Preparation of Acetaminophen sustained-release tablets using melt deposition 3D printing technology and its pharmaceutical evaluation
CHEN Ming,WANG Chen,ZHANG Zhiqiang,DUAN Meitao,REN Jungang,LIN Haiting
(Xiamen Medical College, Xiamen 361000, China)
Abstract:
Objective In this study, the feasibility of fused deposition molding (FDM) technology for the preparation of paracetamol (APAP) tablets was studied, which provided experimental basis for the application of this technology in 3D printing of paracetamol tablets.Methods The preparation of the tablets described in this paper is divided into two steps: using hot melt extrusion (HME) technology to prepare the printed wire; using the fused deposition modeling technology to prepare the molding tablets. During the screening process, the amount and types of excipient, plasticizer, and pore-forming agent were determined. Then the optimal prescription and process parameters were screened by orthogonal design. Finally the content determination, in vitro release, scanning electron microscope and thermogravimetric analysis were evaluated.Results The final optimized 3D printed APAP tablets prescription was including ethyl cellulose (EC) as skeleton excipient, triethyl citrate (TEC) as plasticizer and hypromellose as pore-forming agent, with the ratio of APAP∶Plasticized EC∶HPMC= 25∶50 ∶25, the optimized printing temperature was 160 ℃. The in vitro release rate of tablets was about 50% at 6 hour and was over 90% within 24 hours.Conclusion APAP tablets were successfully prepared using 3D printing technology. The resulting product appears a flat surface and the stacking of layers is relatively smooth. The tables has a slower in vitro release rate compared to APAP tables on the market. The content determination was qualified and the active pharmaceutical ingredient is stable in content at the test temperature.
Key words:  Fused deposition molding technology  3D printing  Acetaminophen  Technology of preparation
Today's Visits:511    Total Visits:2383242
Website copyright:Editorial Board of Journal of Pharmaceutical Research     鲁ICP备17018036号-3     鲁公网安备 37010202001351号
Sponsored by:Shandong Institute for Food and Drug Control Shandong Pharmaceutical Association Address:No.2749 Xinluo Street,High-Tech Zone,Jinan,P.R.China Postcode:250101
Telephone Number:0531-81216586 Email :yaoxueyanjiu@163.com;yaoxueyanjiu@126.com
Technical Support:Beijing Qinyun Technology Co., Ltd.